ABC130 / HCC Panel Metrology

---

---

ABC130/HCC V1.0

(May 2016)

Panel Metrology

ZOT/Stevenage panels with + shaped fiducials

• ZOT_HybridPanel.pdf: Panel top layer

The measurement program for the smartscope requires very few user interactions at the begin:

• ABC130-HCC-Panel-V1.mxi: Smartscope measurement program

In the document below the program steps are discussed. It also includes tips to measure the etch quality.

• Smartscope-ABC130-HCC.pdf: Measurement Program description

To analyse the output file the attached excel spreadsheet can be used:

• Dimensions-Analysis-Master.xlsx: Excel spreadsheet for analysis

The expected positions of the fiducials have been calculated, based on the coordinates from the panel design file. The used values can be seen in the 'Expected Values' sheet of the analysis file. All calculated numbers are based on the numbers with a yellow background and whenever possible these cells are referenced. The sheet '!ExpectedData' shows the expected values again in the same format as the output file, to allow easy comparisons.

To analyse a new measurement the following steps are required:

• open the analysis spreadsheet with excell
• open the output file with excel
  • it is important to choose the right options when importing the csv file so that all columns are separated
• cope the measurement results
• go to the 'Measurement' sheet in the analysis file
• paste the measurement values by clicking on the top left cell (A1);
  • right click to open the special paste options
  • choose 'Values' (this will only paste the numbers, but keep the format of the spreadsheet, including the colours)
• go to the 'Summary' sheet to see all the plots

In the 'Measurement' sheet the cells which contain the comments as well as the step numbers and the step title are in green because they have no influence on the analysis. The red cells are used for numbers that are not important or are not used. For example the Z coordinates from points is not used because the height measurements are done separately. All numbers with a white background are important and used for the analysis.

Flex height

To measure the height of the flex with respect to the FR4 a new program is used, which utilized the touch probe. Measured are the landing pads, the FR4 close to the hybrid caps and the ASIC pads. For each hybrid the FR4 plane is created and set as 0, then the other points are written to file. This allows to check the flatness of a hybrid with respect to the FR4 carrier and also look at the landing pad heights.

• ABC130HCC-fullPanel_Touch.mxi: Height measurement of full panel

Comments:

Height difference between Panel landing pads and ASIC pads caused by adhesive (bondply) that connects laminate to FR4 (frame) but is not under the hybrid

approximately 50um height difference -> seen with smartscope

Zot Panels (May 2016)

• Total-Summary-Zot-May2016.xlsx: Summary of all Zot Panel measurements

Stevenage Panels (June 2016)

• Total-Summary-Stevenage-June2016.xlsx: Summary of all Stevenage Panel measurements

Zot & Stevenage after SMD population (July 2016)

Most of the 0201 capacitors (data lines...) are missing (expected by Norcott due to very small size of components).

All Stevenage hybrids lifted from panel (large bow without vacuum), Zot panels are fine.

RP1 and RP2 wrong orientation (and some are missing)

Below is a detailed list of the missing/failed SMD components, and it can be seen in the attached file as well.

• VisualInspection_19-07-16.xlsx: List of failed components after SMD population
• SMD-components_V2.pdf: SMD component list

List with current status of panels and hybrids

• swapped hybrid 4 from Panel I with hybrid 4 from Panel III

Panel	Hybrid	C5	C7-C12	other	Comment
RP1 and RP2 wrong orientation on all panels (some missing)
Stevenage I Liverpool;RAL	delamination; RFIDPN shifted
Stevenage I Liverpool;RAL	0	n/a			ASIC populated, tested OK
Stevenage I Liverpool;RAL	1	n/a			ASIC populated, tested OK
Stevenage I Liverpool;RAL	2	n/a			ASIC populated, tested OK
Stevenage I Liverpool;RAL	3	n/a			ASIC populated, tested OK
Stevenage I Liverpool;RAL	4	n/a			ASIC populated, tested OK (from Panel III)
Stevenage I Liverpool;RAL	5	n/a			ASIC populated, tested OK
Stevenage I Liverpool;RAL	6	n/a			ASIC populated, tested OK
Stevenage I Liverpool;RAL	7	n/a			ASIC populated, tested OK
Stevenage II used	very little delamination
Stevenage II used	0	n/a	n/a	RFID, NTC2 tombstone, C3, R1
Stevenage II used	1	n/a	n/a	RFID, C2, C3, C4, C6
Stevenage II used	2	n/a	n/a	RFID, C1, C3, C4
Stevenage II used	3	n/a	n/a	RFID, C1, C2, C3, C4, R2, CR5 shifted
Stevenage II used	4	n/a	n/a	RFID, C2, C3, C4, C6, NTC2, CP6 shifted
Stevenage II used	5	n/a	n/a	RFID, C1, C2, C3, R1
Stevenage II used	6	n/a	n/a	RFID, C1, C3, C4, C6, NTC2
Stevenage II used	7	n/a	n/a	RFID, C3, C4, R1
Stevenage III Liverpool
Stevenage III Liverpool	0				after cleaning 0201 capacitor+pads broken
Stevenage III Liverpool	1	n/a			ASICs populated, tested OK; used for module (04/09/2016)
Stevenage III Liverpool	2				ASICs populated first test not working
Stevenage III Liverpool	3				after cleaning 0201 capacitor+pads broken
Stevenage III Liverpool	4	n/a			ASIC populated, tested failed (no ABC ID); from Panel I
Stevenage III Liverpool	5	n/a			ASICs populated Test failed (no HCC address)
Stevenage III Liverpool	6	n/a	n/a
Stevenage III Liverpool	7		n/a
Stevenage IV US	small delamination
Stevenage IV US	0	n/a	n/a
Stevenage IV US	1	n/a	n/a
Stevenage IV US	2	n/a	n/a	C3, C4, R1
Stevenage IV US	3	n/a	n/a	C3, C4, CP6
Stevenage IV US	4	n/a	n/a	C3, C4, C6, R1
Stevenage IV US	5	n/a	n/a	C3, C4, C6
Stevenage IV US	6	n/a	n/a	C3, C4
Stevenage IV US	7	n/a	n/a	C3
Stevenage IX RAL	right Test Coupon; very little delamination; left test coupon removed
Stevenage IX RAL	0			RFID
Stevenage IX RAL	1	n/a		NTC2 tombstone
Stevenage IX RAL	2
Stevenage IX RAL	3	n/a
Stevenage IX RAL	4				failed electrical circuit
Stevenage IX RAL	5
Stevenage IX RAL	6				failed electrical circuit
Stevenage IX RAL	7				used for Liverpool module (08/09/2016)
Stevenage V US	some delamination
Stevenage V US	0		C8, C10, C12	NTC2 tombstone
Stevenage V US	1	n/a	C8-C12	NTC2 tombstone
Stevenage V US	2	n/a	n/a	R1
Stevenage V US	3	n/a	n/a	R1
Stevenage V US	4	n/a	n/a	R1, C4
Stevenage V US	5	n/a	n/a	C3, C4
Stevenage V US	6	n/a	n/a
Stevenage V US	7	n/a	n/a
Stevenage VI used	very small delamination
Stevenage VI used	0	n/a	C7, C8, C9, C11, C12	NTC2 tombstone
Stevenage VI used	1	n/a	n/a	NTC2 tombstone, NTC1, C1, C3
Stevenage VI used	2	n/a	n/a	C3, C4, C6, CP10
Stevenage VI used	3	n/a	n/a	C3, C6, CP10, RFID
Stevenage VI used	4	n/a	n/a	C3, C4, C6, R1
Stevenage VI used	5	n/a	n/a	C3, C4, RFID shifted
Stevenage VI used	6	n/a	n/a	C3, C4, R1
Stevenage VI used	7	n/a	n/a
Stevenage VII RAL	hybrid 2 & 5 one tab brocken [bottom]
Stevenage VII RAL	0
Stevenage VII RAL	1	n/a
Stevenage VII RAL	2	n/a
Stevenage VII RAL	3	n/a
Stevenage VII RAL	4	n/a
Stevenage VII RAL	5	n/a
Stevenage VII RAL	6	n/a
Stevenage VII RAL	7		C11, C12	RP2 OK	0201 capacitor pad brocken
Stevenage VIII used	very little delamination
Stevenage VIII used	0	n/a	n/a	NTC2 tombstone, C3, R1
Stevenage VIII used	1	n/a	n/a	C3, C4, CP11
Stevenage VIII used	2	n/a	n/a	C1, C2, C3, C4, C6	failed electrical circuit; used at Birmingham
Stevenage VIII used	3	n/a	n/a	C1, C4, C6	failed electrical circuit
Stevenage VIII used	4	n/a	n/a	R1, R2, C1, C3, C4, C6, CP1 shifted, CP11
Stevenage VIII used	5	n/a	n/a	C1, C3, C4, C6
Stevenage VIII used	6	n/a	n/a
Stevenage VIII used	7	n/a	n/a
Stevenage X US
Stevenage X US	0
Stevenage X US	1				failed electrical circuit
Stevenage X US	2				failed electrical circuit
Stevenage X US	3	n/a	C8, C9, C10, C12
Stevenage X US	4	n/a	n/a
Stevenage X US	5	n/a	n/a	C3
Stevenage X US	6	n/a	n/a	C3, C4, R1
Stevenage X US	7	n/a	n/a
ZOT A used	RFIDPN, RFIDTC (both), some delamination
ZOT A used	0	n/a		RFID
ZOT A used	1	n/a		RFID
ZOT A used	2	n/a		RFID
ZOT A used	3	n/a	C7, C8, C9, C10, C12	RFID, CP11 (1 add. SMD)
ZOT A used	4	n/a	n/a	RFID
ZOT A used	5	n/a		RFID
ZOT A used	6			RFID
ZOT A used	7	n/a		RFID
ZOT B available
ZOT B available	0	n/a	C8, C10, C12	NTC2 tombstone
ZOT B available	1	n/a	n/a	NTC2 tombstone
ZOT B available	2	n/a	n/a	R1
ZOT B available	3	n/a	n/a	R1
ZOT B available	4	n/a	n/a	R1
ZOT B available	5	n/a	n/a
ZOT B available	6	n/a	n/a
ZOT B available	7	n/a	C11
ZOT C used
ZOT C used	0	n/a	n/a	NTC2 tombstone
ZOT C used	1	n/a	n/a	C3
ZOT C used	2	n/a	n/a	C3, C4, R2, RFID
ZOT C used	3	n/a	n/a	C2, C3, C4, C6, R2, RFID
ZOT C used	4	n/a	n/a	C3, C4, R1, R2
ZOT C used	5	n/a	n/a	C1, C3, C4, C6, NTC2
ZOT C used	6	n/a	n/a	C3, C4
ZOT C used	7	n/a	n/a	C3, C4, R1
ZOT D used Liverpool	some delamination (at landing pads of hybrid 1, 3 [top])
ZOT D used Liverpool	0				ASIC populated, tested OK, Module W668
ZOT D used Liverpool	1	n/a			ASIC populated, tested OK, Module W683
ZOT D used Liverpool	2	n/a			ASIC populated, tested OK, Module W680
ZOT D used Liverpool	3	n/a			ASIC populated, tested OK, Module W682
ZOT D used Liverpool	4	n/a			ASIC populated, tested OK, Module W682
ZOT D used Liverpool	5	n/a			ASIC populated, tested OK, Module W680
ZOT D used Liverpool	6	n/a			ASIC populated, tested OK, Module W683
ZOT D used Liverpool	7	n/a			ASIC populated, tested OK, Module W668

---

---

-- SvenWonsak - 17 May 2016